info@designmind.co.za 083 454 1620

logo

 

LOGIN INTO YOUR ACCOUNT

 

BUILD NEWS

All news Interior & Decor News Design News Landscape News Property News Build News
 
Monday, 12 September 2016 11:56

Snazzy headboard with fabric scraps

Written by 
Rate this item
(0 votes)
| | Home-Dzine|

Here's a great way to use up fabric scraps, or fabric from the bargain bin, to make a snazzy headboard that is colourful and eye-catching.

Make a colourful headboard with a patchwork-effect using scraps of fabric or fabric from the bargain bin at your local fabric store, some thin foam, and a few tools and supplies available at your local Builders.

Fabric scraps to make the size of headboard you require

Thin foam for the patchwork squares (approx. 2cm thick)

BisonBord - cut to the size of your headboard

3mm Masonite or Hardboard - cut for the individual squares

Sprayable adhesive

20mm screws

Roll of duct tape

Bosch Tacker or heavy-duty staple gun

Keyhole brackets and screws to mount onto the wall

1. Determine the size of the headboard required for your particular bed and then divide this into equal sections for the patchwork squares. Have the BisonBord and Masonite or Hardboard cut to fit. Mark the layout for the squares on the BisonBord, on what will be the back of the headboard.

2. Cut the foam to the size of the individual Masonite or Hardboard squares and secure to the board with sprayable adhesive.

3. Cut the scrap fabric to fit over the top and sides of the square, allowing just enough for the fabric to be stapled at the back of each square. Make sure that the staples do not protrude too much - tap with a hammer to flatten if necessary.

4. Line up the wrapped squares face down in your desired pattern. Use duct tape to attach the squares together and hold the pattern in place.

5. Using the drawn guide on the back of the headboard [1 above], use 20mm screws to attach the squares to the front of the headboard. Use 2 screws per square.

6. Attach keyhole brackets to the back of the BisonBord to hang the headboard on the wall.

GOOD TO KNOW: If you need to cover up the edges of the BisonBord, use iron-on or glue on edging strips in a colour that complements the finished colours of your headboard.

Additional Info

  • Source: Home-Dzine
  • Website: www.home-dzine.co.za/
Read 692 times
DesignMind

A smart digital space to market your building service or solution

List first to get ranked first!

DesignMind is a free on-line market space that showcases building or interior design services, building and installation services and building products and solutions in one easy to search on-line space. The site makes it quick and easy for anyone to source a range of products and services that meet any need or application – and simple to geo-locate and connect with the closest suppliers in seconds.

Suppliers get a suite of modern media tools to list solutions and to post content and news - and the functions to self-manage profiles and product and service pages hosted on the site. Requests for quotes, service or information get routed to suppliers Inboxes instantly.

Smart on-line marketing in a box
The most effective and efficient way for suppliers and customers to connect

Get seen. Showcase your products, services, search tags, images and information in our easy-to-use solutions directory and get found in keyword searches instantly. Update your information anytime.

Get pinned. Show up on our map in searches for the closest supplier or service provider. Every product or service listed gets geo-tagged automatically. Your pin links to your solution and contact info.

Get leads. A service request button on every solution page you create makes it easy for anyone to ask for a quote, service or more information. Leads get routed to your Inbox instantly.

Get liked. Our visitors recommend, share and rank solutions they like, giving others the function to source the most liked or best ranked options - and the peace of mind that good references offer.

Get noticed. Use our smart publishing engine to push your news and information to the audiences you’re targeting. Get featured in our weekly newsletter, Facebook, Twitter and iPad App spaces.

Get Ad space. Advertise anything on promotion or special for free. Your special offer gets found in keyword or category searches - or located in searches for specials in a specific area.

Get networking. Use our free trade networking service to make industry contacts and share information. Our smart social media tools make it easy to interact with contacts.

Related items

  • Waterproof a shower

    Failed or poor waterproofing is often to blame for tiling failures, leaks and costly repairs. Bear in mind that tiling itself is not inherently waterproof, and therefore it is essential to have properly detailed and installed waterproofing behind tiled surfaces.

    TAL shares practical advice on how to waterproof a shower with TAL’s Sureproof flexible and seamless rapid-setting two-component waterproofing system.

    GOOD TO KNOW: Allow plenty of time to complete this project, as the waterproofing system requires about 24 hours to dry before tiling can commence.

    Preparation

    Start the process by priming the surface and ensure it is in good condition, clean and dry, and has a moisture content of less than 5%. If necessary, the shower surface can be shot-blasted to give the tile adhesive extra grip, before being sealed with a layer of TAL Floor Primer. If the existing surface is dense and smooth, apply a slurry comprising TAL Floorkey and TAL Rapidfix.

    1. It is important to allow for any movement. Apply a 10mm bead of sanitary silicone to all internal corners and joints around the floor waste, taps and rose plumbing.

    2. Combine the two ingredients of TAL Sureproof together. Use a mechanical mixer or attach a mixer to your drill.  Add the powder to the liquid and mix until a creamy, lump-free consistency is obtained. Allow the mix to stand for three minutes and then stir again.

    3. Apply the first coat of TAL Sureproof to the wall and floor corners. Immediately bed the TAL Sureproof Membrane (200mm wide) into the wet Sureproof [see below]. The Sureproof Membrane must be pushed into the corners, ensuring the entire interface is covered with the membrane. Ensure there are no wrinkles or air bubbles trapped beneath the membrane.

    4. Apply a second coat of TAL Sureproof to saturate the membrane completely before the first coat dries.

    5. Where the waste is flush with the floor, place the membrane around and down into the waste.

    6. For the main shower wall and floor surfaces, apply the first coat of TAL Sureproof to the dry, primed surface with a short hair paint roller or brush, and allow approximately two hours to dry. Apply the second coat in a different direction to ensure complete coverage, avoiding air entrapment or pinholes. Allow the TAL Sureproof system to dry for 24 to 36 hours before fixing the tiles.

    When tiling, modify the tile adhesive and grout with TAL Bond Powder or Bond Liquid to add flexibility and water resistance to the tiling installation, and apply a silicone sealer to all the perimeter joints.

    GOOD TO KNOW: Use of the shower is not recommended for 72 hours after completion of the tiling to ensure that the installation has cured fully.

    As a final touch, seal the grout joints with TAL Grout Sealer. This will ensure your newly-installed shower not only looks good, but is also easy to clean. If in any doubt visit www.tal.co.za

  • Quick and easy bamboo headboard

    Here's a wonderful quick and easy way to add a decorative bamboo headboard and turn any bed into a feature.

    All you need to turn any bed into a focal point is a bamboo blind or screen, and to mount this above the bed. If you can't find a ready made blind, or don't have one that you can upcycle, you can buy bamboo stakes at many garden centres and nurseries around the country.

    Assemble individual bamboo stakes using natural twine or thin sisal rope that blends with the natural bamboo finish. Once assembled you can leave the bamboo in it's natural state or add a wood tint using Woodoc interior sealer.

    Add a couple of hangers at the back to mount the bamboo headboard onto the wall, or add a 12mm plywood backing board and make it long enough to rest on the floor.

  • Make a chunky platform bed

    Pine scaffolding planks are perfect for making this chunky platform bed. You can buy these at most timber merchants and they are reasonably priced if you are prepared to put in the effort of sanding them smooth, or lookout for reclaimed scaffolding planks online.

    There are no measurements provided, but the size of frame and base is determined by the size of your mattress. In this way, you can use the method shown here to make a chunky platform bed to any size. 

    The process for making the outer frame is simple: half-overlap joints are used to join the top and bottom planks to the sides. These are secured using glue and nuts and bolts. If you prefer a more decorative finish, shop for round-head nuts, or caps that can cover up the nut heads. 

    GOOD TO KNOW: If you want to make the frame wider, use biscuit joints or a Kreg pockethole jig to join two planks together.

    Leave the timber in its natural state, or stain with Woodoc Gel Stain or a tinted Woodoc Interior Sealer.

  • Dress up plain curtains

    In this project we combine peony pink curtains with lime green tape trim to add a touch of elegance to a dining room. This designer touch elevates the entire room, and it’s such an easy change you can make to your curtains.

    Curtains

    Decorative trim - enough for both curtain panels

     Iron-on tape or decoupage webbing

    Tape measure

    Iron

    Ironing board and towel

    1. Start by measuring how far into the panel you'd like the trim to be placed. Lay the curtain on a large flat surface. Use a tape measure to determine how far into the panel you’d like to place the trim. your trim to be placed. Our tape is 4cm in from the edge.

    2. Place a strip of iron-on tape along both edges of the green trim, working in about 30cm sections at a time.

    GOOD TO KNOW: If your trim is wide use iron-on tape at both edges. For narrow trim you may only need one strip of tape.

    3. Turn the trim over and onto the top front of the curtain panel so the iron-on tape is facing down. Use a hot iron to fuse the tape trim to the curtain panel.

    GOOD TO KNOW: If you are using thick trim, check that enough heat is applied to bond the trim to the curtain panel or apply more heat with the iron.

    4. Once the trim is secured on the first section, turn the corner of the panel over to steam the edge to create a finished look.

    5. Once the long edges are done you can move to the bottom of the curtain panel. In this project we added the tape along three edges of the panel, with a 45-degree angle corner. However, to save on tape or avoid creating a corner, simply fold the trim and tape over the edge and finish your edge.

    6. To make the corner, fold the trim at a 45 degree angle and then iron the corner down with iron-on tape.

    7. With a small piece of tape, iron down the excess trim. Work your way down the bottom edge of the panel until you get to your second corner and repeat this step.

    Now you can work your way back up the edge of panel to the top to complete the trim! Once your trim is secured, leave your panels overnight before hanging them.

  • Upcycle lampshade frames into plant stands

    Wire lampshade frames

    Cutter pliers

    Rust-Oleum spray paint in your choice of colour

    Potted plants to fit into frames

    1. Use cutting pliers to remove the lamp housing from the top (centre) of the frame. If you find this difficult to do using pliers, use a Dremel MultiTool and cutting disc.

    2. Put down some newspaper and spray your plant stands using Rust-Oleum spray paint. Copper metallic is trendy right now and you will find Rust-Oleum Metallics at your local Builders.

    3. If you are potting up your own bought plants, make sure the pots fit into the frame before potting your new plants. This is the time of year when bulbs can be found at your local nursery, so be sure to include a colourful bulb or two in your display.

     

Leave a comment